Skip to content
R8 insulated flex ductwork installed in an attic during a ductwork replacement by Chubby's HVAC near Corona, CA

Ductwork · Corona, CA

Ductwork Replacement in Corona, CA

Ductwork replacement in Corona, Norco, Riverside and Eastvale. Chubby's HVAC tests static pressure, designs duct systems with a Manual D and installs R8 insulated flex duct and media filter cabinets.

Request Service

You can also text (951) 496-7973.

Ductwork Replacement From Chubby's HVAC

Chubby's HVAC replaces and installs ductwork in homes in Corona, Norco and surrounding areas. Many companies swap the equipment and leave the old ducts in place, and that is how a new system ends up with the same hot bedroom. Most of our system installs include new ductwork for that reason.

Static Pressure Testing

We measure total external static pressure to see whether the ducts are choking the airflow. Static pressure works like blood pressure. When it is high, the system is straining even if cold air still reaches the vents.

Manual D Duct Design

We size the supply runs, the return drop and the filter grille to match the system and the house, using a Manual D duct design.

R8 Flex Duct Installation

We install R8 insulated flex duct, the most common duct in California homes. We support each run so it does not kink, and seal the plenum and every connection with mastic tape so conditioned air stays in the ducts.

Metal Duct, Riser Pipe and Round Duct

We also install square metal duct, riser pipe and round metal duct when a home calls for it, such as the older Victorian homes in Corona.

Flex duct runs supported and sealed in an attic during duct replacement by Chubby's HVAC, serving Corona and Norco, CA

Ductwork Types Compared

About 98 percent of the homes we work in across Corona, Riverside and surrounding areas have flex duct. Older homes, including the Victorian homes in Corona and many homes from the 1970s and 1980s, often have metal duct.

Duct TypeWhere You Find ItCostEfficiency
R8 Insulated Flex DuctIt is in about 98 percent of California homes.It costs the least of the three.It is efficient and lasts when it is supported and sealed.
Square Metal Duct and Riser PipeIt is in older homes, including Victorian homes and many homes from the 1970s and 1980s.It costs much more than flex duct.It tends to leak air at the joints.
Insulated Round Metal DuctIt is mostly used in commercial buildings.Material runs about $100 per 3 foot length, and one long run can reach $3,500 installed.It is insulated, but the cost rarely makes sense for a home.

For California homes, we recommend R8 flex duct over metal. It is more efficient, it lasts longer, and it costs far less.

Air Filtration and Media Filter Cabinets

Chubby's HVAC improves air filtration for homes in Eastvale, Fontana and surrounding areas with high-capacity media filter cabinets, such as a 20 by 30 by 5 inch MERV 13 setup. We expand the return drop to fit the cabinet and seal the transitions so dust cannot get around the filter.

Return air grille and filter after an air filtration upgrade by Chubby's HVAC, serving Eastvale and Fontana, CA

Why Hire Chubby's HVAC for Ductwork Replacement

Chubby's HVAC replaces ductwork in Riverside, Corona and surrounding areas as a licensed C-20 contractor, CSLB #1145051, and we are insured.

  • Testing. We measure static pressure before the new ductwork goes in and after.
  • Design. We size the ducts with a Manual D design, not by guesswork.
  • Sealed Connections. We seal the plenum and every connection with mastic tape.
  • Documentation. We photograph the old and new ductwork so you can see the difference.
  • Honest Choice. If your ductwork is designed right and under 20 years old, we tell you to keep it.

Areas Served

Chubby's HVAC works from Corona across the Inland Empire and surrounding areas, up to 75 miles out.

  • Corona
  • Eastvale
  • Riverside
  • Norco
  • Fontana

More services

Other Services From Chubby's HVAC

New outdoor AC condenser on a level pad after an AC installation by Chubby's HVAC near Corona, CA

AC Installation

We size and install new air conditioners, furnaces and ductless mini-splits.

AC Installation
Condenser coil cleaning during an AC maintenance visit by Chubby's HVAC, serving Corona and Eastvale, CA

AC Maintenance

We clean the system and take readings before and after every visit.

AC Maintenance

About us

Work With Chubby's HVAC

Chubby's HVAC Home Services works out of Corona and is licensed and insured, CSLB #1145051. We test the system before we recommend work and send you the readings and photos when the job is done.

Gas furnace in an attic ready for the $79 heating tune-up and safety inspection from Chubby's HVAC in Corona

Heating season

Book the $79 Heating Tune-Up

We clean the burners and blower, check and adjust the gas pressure, test for carbon monoxide and check duct airflow. It takes about an hour and a half.

Prices

Posted Prices

$3,500 to $5,500

New Duct System

A new duct system usually adds this much to a system replacement.

$14,000 to $16,000

Entry and Mid-Range System

A full system swap in Southern California usually lands in this range, without ductwork.

$18,000 to $22,000

High-Efficiency System

High-efficiency systems with more features usually land in this range, without ductwork.

$88

Diagnostic Visit

We charge $88 for a diagnostic visit and credit it toward the repair when you go ahead.

$79

Heating Maintenance and Safety Inspection

We clean the burners and blower, check the gas pressure, test for carbon monoxide and check duct airflow.

Every new system and duct price is confirmed in writing after we measure the home.

Chubby's HVAC working on an outdoor air conditioner condenser for a homeowner in the Corona, CA area

Same day, next day or within 48 hours

Schedule Service With Chubby's HVAC

Call or text Chubby's HVAC at (951) 496-7973, or send the request form, and tell us what the system is doing.

FAQ

Ductwork Questions

How much does new ductwork cost?

In Southern California a new duct system usually runs $3,500 to $5,500. The price depends on the size of the home and the number of runs. We give you an exact price after we measure the house.

Why are some rooms in my house hot while others are freezing?

Uneven temperatures usually come from imbalanced airflow in the ductwork or poor workmanship on the original install. Checking the static pressure against the manufacturer's specifications is the first step to finding the cause.

Is metal ductwork better than flex duct?

Not for most California homes. Metal duct costs much more, tends to leak air at the joints and is mostly used in commercial buildings. R8 insulated flex duct is more efficient and more affordable for a home.

When can I keep my existing ductwork?

When it was designed correctly, tests well for static pressure and is under about 20 years old. We show you the readings and let you decide whether to keep it or replace it with the new system.

What is a Manual D?

A Manual D is a duct design. It sizes each supply run, the return and the filter grille for the airflow your system needs, based on the load calculation we do for the house.

Do you replace ductwork when you install a new system?

Most of our installs include new ductwork, because a new system on old, poorly sized ducts will not perform. A duct system usually adds $3,500 to $5,500 to the cost of a new system.

Can you add a better air filter to my system?

Yes. We install high-capacity media filter cabinets, such as a 20 by 30 by 5 inch MERV 13 filter. We modify the return so the cabinet fits and seal it so air cannot bypass the filter.

Call now Text us